Showing 1–24 of 28 results

Conax BSWS Series – Bearing Sensor Wire Compression Seal Feedthrough

  • Stainless Steel Fitting
  • For Bearing Oil Sealing
  • Easy Installation – No “Potting”
  • Seals 2 to 14 Wires
  • Pressure*: to 50 PSI (3.4 bar)
  • Temperature Range: Ambient to 100°F (37.8°C)
  • Field Adjustable
  • Reusable Fitting

Conax EG Series – Power Compression Seal Feedthrough

  • Seals 1 Electrode or Element
  • For Gas or Non-Conductive Liquid
  • Stainless Steel Reusable Fitting
  • “Soft Sealant”
  • Electrode Easily Assembled or Replaced in Field

Conax EGT Series – Power Compression Seal Feedthrough

  • Electrode Teflon Sealing Gland
  • Seals 1 Electrode or Element
  • For Gas or Non-Conductive Liquid
  • Stainless Steel Reusable Fitting

Conax FCA Series – Fiber Cable Assembly

  • Transmission Loss: Less than 0.3db typical (not including connectors).
  • Temperature Rating: -4°F to +185°F (-20°C to +85°C). Higher temperature models are available in some configurations. Please consult factory.

Conax FSA Series – Fiber Optic Feedthrough

  • Helium Leak Rate: 1 x 10-6 scc/sec typical
  • Transmission Loss: Less than 0.3db typical (not including connectors)
  • Pressure Rating: 1000 PSIg (70 bar) standard, up to 3000 (207 bar) PSIg optional
  • Temperature Rating: -4°F to +185°F (-20°C to +85°C). Higher temperature models are available in some configurations. Please consult factory.

Conax HD Series – High Density Feedthrough Assemblies

  • Sheath Material: 300 Series SST, 4.5″ nominal length
  • Temperature Range: -112°F to +250°F (-80°C to +120°C)
  • Vacuum Rating: 5 x 10-6 mm HG @ 68°F (20°C)
  • Leak Rate: 1 x 10-9 scc/sec He @ 68°F (20°C), 1 atm. applied
  • Voltage Rating: 100 VDC
  • Amperage Rating: 500mA
  • Feedthrough Pressure Rating @ 68°F (20°C): 5000 psi (345 bar)

Conax HEGPK Series – Power Compressions Seal Feedthrough

  • Seals one electrode, conductor or element
  • Temperature Range: Vacuum to 7,700 PSIg (531 bar)
  • Voltage 8000 VDC
  • Amperage to 200 amps
  • Supplied with or without conductor

Conax HL Series – Hazardous Location Conduit Seal

  • Stainless Steel Fitting
  • For Gas or Liquid
  • Easy Installation -No “Potting”
  • Seals 1 to 12 Wires
  • Pressure*: Vacuum to 10,000 PSI (690 bar)
  • Rated: 600 Volts to 55 Amps

Conax HPEG Series – Power Compressions Seal Feedthrough

  • Each unit has a stepped electrode. Larger diameter of electrode is on the body side.
  • Electrode is copper (CU), stainless steel (SS) and nickel (NI)
  • Voltage rating 2000VDC
  • Body material is 316SS, ASTM 479
  • SST nuts and washers for NI and SS, brass for CU
  • All prices include a pressure test at 68°F

Conax HPT Series – 2-Wire Temperature Transmitter for RTDs

The Conax Model HPT is a low cost, 2-wire, non-isolated temperature transmitter for RTD sensors, and is designed to fit in our popular T11 model terminal head.The HPT housing has a removable base allowing access to the electronics for the purpose of temperature range changes, which are easily accomplished with plug-in resistors

Conax HPTI Series – 2-Wire Temperature Transmitter for RTDs

The Conax Model HPTI is a low cost, 2-wire, non-isolated temperature transmitter for RTD sensors, and is designed to fit in our popular T11 model terminal head.The HPTI housing has a removable base allowing access to the electronics for the purpose of temperature range changes, which are easily accomplished with plug-in resistors

Conax PDT-400 Series – PC Programmable DIN Rail Mount Transmitter for Thermistors

The Conax Model PDT-400 is a slim DIN rail mount programmable 2 wire transmitter, featuring a state-of-the-art microprocessor-based design that enables full configuration with user friendly configuration software.

Conax PG Series (PG, MIC, MPG) – Compression Seal Fitting

Conax Technologies Model PG Packing Glands provide pressure/vacuum sealing for tubes, probes, pipe, cable or any single element assembly (not electrically isolating), including thermocouples, RTDs, thermometers, thermistor probes, capillary tubes, tubewells, multi-pair cables and analyzer sample tubes. PG glands seal against gases and liquids and resist element movement under pressure.

Conax PGS Series – Split Compression Seal Fitting

  • Seals 1 Element
  • For Gas or Liquid
  • Stainless Steel Fitting
  • Simple Assembly – Insert Element, Torque Cap
  • Replaceable Sealant Permits Repeated Use Of Fitting

Conax PL Series – Multi-Wire Power Compression Seal Feedthrough

  • Stainless Steel Fitting
  • For Gas or Liquid
  • Easy Installation -No “Potting”
  • Seals 1 to 12 Wires
  • Pressure*: Vacuum to 10,000 PSI (690 bar)
  • Rated: 600 Volts to 55 Amps

Conax PTH-400 Series – PC Programmable Transmitter for RTDs and Thermocouples

All input types and range parameters are easily configurable with user-friendly technology. No power supply is required for programming. The PA-400 programming adapter and the graphic user interface software operate under Windows® operating systems through the PC’s RS232 serial port.

Conax Resistance Temperature Detectors (RTD) Assemblies

Conax Buffalo Technologies offers a complete line of dependable, ruggedized RTDs, ranging from thin film platinum sensors to wire wound sensor configurations available in platinum, nickel and copper. Conax can custom design RTD configuration to suit your specific needs, from trimmable RTDs, which provide added field installation flexibility, to fast response RTDs, for applications where response time is critical.

Conax TG-24/MTG-24 Series – Instrumentation Wire Compression Seal Feedthrough

This assembly consists of a Conax Technologies manufactured TG Feedthrough provided with a sealant and 24 AWG solid insulated thermocouple grade wires or copper wires. The feedthrough is furnished with 24″ of wire on each side. Longer wire lengths can be furnished as required.

Conax TG/MTG Series – Instrumentation Wire Compression Seal Feedthrough

  • Pressure/Vacuum Compression Seal
  • Stainless Steel Reusable Fitting
  • Soft Sealant
  • Wires Easily Assembled or Replaced In Field
  • Temperature Range From -300°F to +1600°F (-185°C to +870°C)
  • Pressure*: Vacuum to 10,000 PSI (690 bar)
  •  Seals 1 to 16 Elements